Tying a chod rig is an essential skill for anglers who want to catch carp in challenging conditions. The chod rig is a versatile setup that can be fished over various lakebeds, including silt and debris. It is also effective in weed, though it can become suspended and look unnatural in heavier stuff. In this article, we will guide you through the process of tying a chod rig with a diagram to help you understand the steps better.
To tie a chod rig, you will need a few materials, including a spool of REVOLVE™ Stiff rig bristle filament, Duropoint® Chod hooks, a Micro hook ring swivel, and a lighter. You will also need scissors and two-knot pullers. We will show you how to prepare these materials and tie the chod rig step by step. We will also provide tips and tricks to help you set up the rig correctly and answer some frequently asked questions about chod fishing.
By the end of this article, you will have a good understanding of how to tie a chod rig and be ready to catch carp in challenging conditions. So, let’s get started!
Key Takeaways
- Understanding the chod rig and its versatility is essential for carp fishing in challenging conditions.
- Tying a chod rig requires specific materials and tools, including REVOLVE™ Stiff rig bristle filament, Duropoint® Chod hooks, and a Micro hook ring swivel.
- Following the step-by-step guide, preparing the materials, and setting up the chod rig correctly will increase your chances of catching carp.
Understanding the Chod Rig
The Chod Rig is a popular setup among carp anglers because of its versatility and effectiveness. It is designed to be fished over a variety of lakebeds, particularly silt and chod (general bottom debris), and can also be used in weed, though it can become suspended and look unnatural in heavier stuff.
The Chod Rig consists of a short stiff hook link, a buoyant bait, and a lead. When cast out, the lead sinks to the depths while the hook link and bait fly back up the line/leader. Once the lead has hit the bottom, the baited rig then slowly sinks until it encounters the first piece of weed or chod, where it’ll then settle and start fishing.
One of the keys to the Chod Rig’s effectiveness is its presentation. Because the bait is buoyant, it sits above any debris on the lakebed, making it more visible and attractive to carp. Additionally, the short stiff hook link ensures that the hook is always presented in a straight line, increasing the chances of a hook-up.
There are several variations of the Chod Rig, including the Naked Chod Rig, which eliminates the lead and uses a semi-fixed stop to hold the rig in place. This allows the bait to settle more naturally on the lakebed and can be particularly effective in weedy or snaggy areas.
Overall, the Chod Rig is a versatile and effective setup that can be used in a variety of fishing situations. With the right presentation and bait, it can be a deadly tool for catching carp.
Materials Needed
To tie a Chod rig, we will need a few components. Here is a list of the materials required:
- Chod hook
- Chod filament
- Rig ring
- Ring swivel
- Tungsten putty
- Bait floss
- Scissors
- Knot puller x 2
- Lighter
We recommend using Duropoint® Chod hooks along with one of our Bait attachments. We’ll be using a Micro hook ring swivel, but you can also use a hook ring swivel screw, rig ring screw, or Rig ring.
For the Chod filament, we suggest using a spool of REVOLVE™ Stiff rig bristle filament. You’ll also need a top bead and a buffer bead.
When it comes to tungsten putty, we recommend using a rig putty that is easy to mould and can be removed easily.
For the bait floss, we recommend using a strong and durable material that can hold the bait in place.
It’s important to have a good pair of scissors to cut the filament and bait floss. You’ll also need two-knot pullers to tighten the knots.
Finally, you’ll need a lighter to melt the tag end of the Chod filament and create a loop.
With these materials, we can start tying the Chod rig.
Preparing the Materials
We need to gather all the necessary materials to tie a Chod rig. The Chod rig is a bit tricky to tie, but with some practice, it’ll become second nature. Here’s a list of materials we need to prepare before we start:
- Chod hook
- Chod filament
- Rig ring
- Ring swivel
- Tungsten putty
- Bait floss
- Pop-up
- Scissors
We also need a lighter and a lead to melt the ends of the Chod filament and the bait floss. It’s essential to have all these materials in our tackle box before we start.
First, we need to tie the Chod section. We take a 7-inch length of bristle filament and pass it through the eye of the hook so that there is around 40mm at the back of the hook. We then tie a two-turn blood knot to secure the filament to the eye of the hook. We cut the tag end of the filament and melt the end with a lighter to prevent it from fraying.
Next, we tie a rig ring to the Chod section. We take a piece of Chod filament and tie a simple overhand loop knot. We then pass the loop through the rig ring and bring the tag end back through the loop. We pull the knot tight and cut the tag end. We melt the end of the Chod filament with a lighter to prevent it from fraying.
We then tie a ring swivel to the Chod section. We take another piece of Chod filament and tie a simple overhand loop knot. We then pass the loop through the ring swivel and bring the tag end back through the loop. We pull the knot tight and cut the tag end. We melt the end of the Chod filament with a lighter to prevent it from fraying.
To add weight to our rig, we need to use tungsten putty. We take a small piece of putty and mould it around the Chod section, just above the rig ring. We then shape the putty to the desired size and shape.
Finally, we need to attach the bait to our Chod rig. We take a piece of bait floss and tie it to the Chod section, just above the tungsten putty. We then thread a buoyant pop-up onto the floss and tie a hair rig to the end of the floss. We then attach our hook bait to the hair rig.
That’s it! We’ve prepared all the materials needed to tie a Chod rig. In the next section, we’ll go through the steps to tie the Chod rig.
Tying the Chod Rig
To start, we need to gather all the necessary items for tying the chod rig. We will need a spool of chod filament, chod hooks, bait floss, rig rings, rig putty, pop-ups, hair, scissors, and a knot puller.
- First, we need to cut a length of chod filament, around 10-12 inches long.
- Next, we will make a loop at one end of the filament using our thumb and forefinger.
- We will then tie a knotless knot around the loop, making sure to leave a tag end of around 2 inches.
- We will then slide a rig ring onto the tag end of the filament and secure it in place with rig putty.
- Next, we will tie a piece of bait floss to the eye of the hook and thread it onto the chod section.
- We will then attach a pop-up to the hair and secure it in place with a knotless knot.
- We will then tie a two-turn blood knot to attach a micro hook ring swivel to the other end of the chod filament.
- We will then slide a buffer bead onto the chod section and attach it to a lead clip.
- Finally, we will attach a top bead to the chod section and adjust the depth of the rig accordingly.
It is important to use chod hooks when tying the chod rig, as they are specifically designed for this type of rig. Additionally, using slack lines can help the rig follow the contours of the bottom, making it more effective. Fluorocarbon can also be used for the chod section, as it is virtually invisible underwater.
Overall, tying the chod rig can be a bit tricky at first, but with practice, it can become a valuable addition to any angler’s tackle box.
Setting the Chod Rig
Once you have tied your Chod rig, it’s time to set it up for fishing. Here’s how we do it:
- Attach the Chod rig to your mainline using a two-turn blood knot or a figure-of-eight loop knot. Make sure to wet the knot before tightening it to prevent damage to the mono.
- Slide a buffer bead onto the mainline and push it up against the knot. This will act as a shock absorber and prevent the lead from damaging the knot during the cast.
- Tie on a lead clip or a helicopter rig, depending on your preference. Make sure to use a rig putty to secure the lead in place and prevent it from bouncing around during the cast.
- Slide a top bead onto the mainline and push it up against the lead clip or helicopter rig. The top bead should be set at a depth of 1.5 times the depth of the weed or silt you are fishing in.
- Thread a buoyant pop-up onto the hair and attach it to the eye of the hook using a knotless knot or a blood knot. You can also use bait floss to secure the pop-up to the hair.
- Slide a micro hook ring swivel onto the tag end of the Chod section and tie on a tungsten putty to balance the rig. The putty should be positioned a few inches above the hook.
- Thread a bead onto the Chod section and push it up against the tungsten putty. The bead should be large enough to prevent the putty from sliding up and down the Chod section.
- Tie on a hook bait of your choice using a hair rig. Make sure to adjust the length of the hair so that the hook bait sits just above the bead.
- Finally, attach a slack line to the Chod rig to allow the fish to pick up the bait without feeling any resistance. You can use a margin pole or a bank stick to achieve this.
By following these steps, you can create a highly effective Chod rig presentation that will attract even the wariest carp. Remember to experiment with different hook baits and lead setups to find what works best for your fishing style. Good luck!
Tips and Tricks
When it comes to tying a chod rig, there are a few tips and tricks that can help improve your presentation and increase your chances of catching carp. Here are some things to keep in mind:
- Consider the lakebed: The chod rig is designed to be fished over a variety of lakebeds, but it can be particularly effective in weed, debris, and silt. Make sure to adjust the length of your chod accordingly to ensure that your bait is presented at the right depth.
- Use slack lines: When fishing with a chod rig, it’s important to use slack lines to allow the rig to settle naturally on the lakebed. This will help prevent the rig from becoming tangled or caught on any underwater obstacles.
- Experiment with different baits: The chod rig is a versatile setup that can be used with a variety of baits, including buoyant pop-ups and bottom baits. Experiment with different types of bait to see what works best for you.
- Choose the right tackle: When tying a chod rig, it’s important to choose the right tackle, including chod hooks, lead clips, and tubing. Make sure to use high-quality tackle that is designed to withstand the rigours of chod fishing.
- Pay attention to presentation: The key to success with a chod rig is presentation. Make sure to take the time to tie your rig properly and adjust it as necessary to ensure that your bait is presented naturally and enticingly.
- Master the naked chod: The naked chod is a variation of the chod rig that involves fishing without any tubing or lead clip. This can be a highly effective setup in the right conditions, but it requires a bit of skill and finesse to get right.
By keeping these tips and tricks in mind, you can improve your chod fishing skills and increase your chances of catching carp. Remember to experiment with different setups and baits to find what works best for you, and don’t be afraid to try new techniques and approaches. With a bit of practice and patience, you can become a master of the chod rig and catch more carp than ever before.
Frequently Asked Questions
What components are needed for a Chod Rig?
To tie a Chod Rig, you’ll need a few essential components. These include a spool of stiff rig filament, a Chod hook, a bait attachment, a hook ring swivel, a rig ring screw, scissors, a knot puller, and a lighter.
How long should a Chod Rig be?
The length of your Chod Rig will depend on your personal preference and the conditions you’re fishing in. However, we recommend using a rig length of around 6-8 inches.
What is a Helicopter Chod Rig?
A Helicopter Chod Rig is a variation of the Chod Rig. It features a lead that is attached to a leader, which is then attached to the rig. This setup allows the rig to rotate freely around the leader, reducing the chances of tangles.
Do I need putty on my Chod Rig?
While putty isn’t necessary on a Chod Rig, it can help to improve the presentation of your bait. By adding putty to the rig, you can ensure that it sits flush with the lakebed, making it more attractive to feeding fish.
What are the benefits of using a Chod Rig?
One of the main benefits of using a Chod Rig is its versatility. It can be fished over a variety of lakebeds, including silt and debris, making it an excellent choice for carp fishing. Additionally, the Chod Rig is known for its excellent hooking potential, ensuring that you’ll land more fish.
Are there ready-made Chod Rigs available?
Yes, there are many ready-made Chod Rigs available on the market. These rigs are pre-tied and ready to use, making them an excellent option for anglers who are short on time or new to carp fishing. However, we recommend learning how to tie your own Chod Rigs, as this will allow you to customize the rig to your specific needs and preferences.
